Yes, the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 is the correct system for both your 2016 Ultra Limited(FLHTK) and 2021 Road Glide Special(FLTRXS). It fits all FL Touring models Harley Davidson motorcycles.
Your 2014 CVO Breakout(FXSBSE) will use the B&W Biker Bar Motorcycle Tie-Down System # BWMC2302. This fits Harley FX, FLST, and VR models.
An additional B&W Biker Bar Motorcycle Tie-Down System Base # BWMC2300 can be used if you have multiple trailers and do not want to... view full answer...
The B&W Biker Bar Motorcycle Tie-Down Systems such as # BWMC2302 are designed at a specific height to attach to the frame of the bikes they were made for. Flat tires would make the bike lower and cause it not to fit the Bike Bar properly. You would need to air up the tires or place boards or something under the tires so the bike sits up at the proper height. You would want the boards to be secured to the trailer floor as well to avoid slipping in transit. view full answer...
The Adco SFS AquaShed Cover for Bumper Pull Trailer - Up to 16' Long - Gray # 290-46004 will fit trailers up to 106" wide. The Adco SFS AquaShed has cinching ropes and weighted straps to secure the cover on your trailer so that it doesn't billow in the wind, which might cause tears, so your cover will always be secured tightly to the trailer. view full answer...
Yes. The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301 will work on Harley Davidson trikes manufactured before 2014, so your 2014 Harley Davidson Tri-Glide Ultra without any issues. The Biker Bar will connect at the same place on your trike as it would on a regular motorcycle since the frame in that spot is the same. view full answer...
The 2014 Harley Davidson Fat Boy Lo is considered a Softail. This means that the correct biker bar for your Harley is the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Softail, Dyna, V-Rod # BWMC2302. view full answer...
The B&W Biker Bar that you should be using for your 2010 Ultra Classic is the part # BWMC2301 but for your 2014 Softail Deluxe you need the Biker Bar # BWMC2302 instead. Good news is that both options use the same base system so you just need to replace the actual bar instead of the entire kit and for that you need the Replacement Bar # BWMC2302B. This then gives you the entire setup for your Softail Deluxe. view full answer...
The B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 will work great with your Road King FLHR that has the rear air suspension just as long as your frame tubing diameter is 1-1/8-inches or 1-1/4-inches and that tubing is spaced apart 10-inches to 14-1/2-inches at the bottom of the frame.
You will want to have the bike as low to the deck as possible for the lowest center of gravity. The installation instructions are linked for you along with a video. view full answer...
In order to find if the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 will fit your 2021 Harley Davidson Tri Glide you will need to measure. You will be able to use this system as long as your frame tube diameter is 1-1/8" - 1-1/4" and your frame width is 10" - 14-1/2". view full answer...
The B&W Biker Bar Motorcycle Tie-Down System Base with Anchor Plates # BWMC2300 will fit your 2010 Harley Davidson Ultra Classic. This will be just the base mount, though.
If you are wanting the complete system that will be the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301. This system includes the base mount and the clamping bar that will mount on your bike. view full answer...
For the 5-Pole round connector on your 1989 Electra Glide Harley Davidson, like part # PK11502, we have the Pollak 5-Pole, Round Pin Trailer Wiring Connector # PK11501. All you have to do is cut off the 5-Way flat connector on your trailer and then verify which pins carry which functions by using a circuit tester like part # PTW2979 so you can wire your trailer connector up accordingly!
You may need a converter like part # RM-732 which takes individual stop and turn signals (like what... view full answer...
There are a number of different boost jump starters that the Eyelet Cable with X-Connect Adapter for NOCO Boost Jump Starters # 329-GBC007 works with, but not the Harley-Davidson one you mentioned; instead, it will work with the following, each of which is capable of jump-starting your battery so long as it is a wet cell, gel cell, maintenance-free, enhanced flooded, or AGM battery.
- NOCO Genius Boost Sport Jump Starter - 12V - 400 Amp # 329-GB20
- NOCO Boost Plus Jump Starter- USB Port... view full answer...
The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson 1-1/2" Custom Frame # BWMC2304 will fit frame tube diameters between 1-3/8" - 1-1/2" and frame widths between 10" - 14-1/2".
The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring # BWMC2301 is similar and fits the exact from widths but tubes that are 1-1/8" - 1-1/4".
The mounting bases are the same so you could use that portion of his system, but you will need the Replacement... view full answer...
The Jensen Heavy Duty Mechless RV Stereo part # JHD1635BTB is not designed for a motorcycle per say but I don't see any issue using this on your 2007 Harley Davidson Street Glide so long as you have room to mount the stereo and you have access to 12 volt power. The wiring harness that you will need for installation is included (see photo).
I am not sure what you mean by an adapter for your hand controls but in addition to the photo of the wiring harness, I have also attached for you... view full answer...
The B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 is designed for the touring line of Harley Davidson motorcycles. I do recommend verifying your frame has the frame tube diameter of 1-1/8" to 1-1/4" with a width of 10 to 14-1/2". If you have any other dimensions please let me know so I can confirm the correct system for your 2008 Electra Glide Classic. view full answer...
The correct B&W Biker Bar for your 1999 Harley-Davidson FLSTC Softail is the following:
- B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Softail, Dyna, V-Rod # BWMC2302 view full answer...
The stock front tire on a 2011 H-D Street Glide is a 130mm width (size 130/70-18) which is 5.1-inches wide. Our range of motorcycle wheel chocks is shown on the linked page.
For the safest transport you might consider the B&W Bike Bar # BWMC2301 which secures your ride without wheel chocks or tie-down straps rubbing on its paint or chrome. Please see the linked video. view full answer...
XM radio device compatibility can vary depending on the generation of the items. Older systems may not always function with latest-generation items.
But so long as a device such as the SiriusXM Satellite Radio Receiver # 292-101468 has the same connector type as your OEM system they should work well together. I linked a photo of the connector on the above item. view full answer...
Yes, although is may not be as compact as you prefer for a bike, even a touring frame such as the FLHTC. You need the Remote for Rockford Fosgate Hide-Away Receiver, # 292-100262 in addition to the Rockford Fosgate Hide-Away Receiver, # 292-100834; it will not operate just by using your smartphone.
Please note the attached video review. view full answer...
Yes, the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301 is fully compatible with your 2013 Harley Davidson Tri Glide. I confirmed with my contact at B&W. This trailer-mounted carrier includes mounting hardware for the included base plate. Drilling is required for installation.
You can refer to the linked review and installation videos for more details on this carrier system. No straps or tie-downs are required to secure your trike so there is no risk of abrasion to your painted surfaces... view full answer...
The 15" wheel I recommend for your boat trailer is the Americana Galvanized Steel Spoke Trailer Wheel # AM20534. This has a 6 on 5-1/2" bolt pattern like what you're needing and we actually have a review from a customer talking about how this was the only one they found to work with disc brakes.
Attached is a review video as well as a photo of the review for you to check out. view full answer...
Go To Results